As an Amazon Associate I earn from qualifying purchases.
1. Atnsinc #ad
6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino #adAtnsinc #ad
- The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Great packing in a box : 6 pcs uln2003 Stepper Motor + Driver Board with a little gift.
Drive module board sizein: 1. 37 * 1. 18 * 06in; stepper Motor diameter: 1. 06in; stepper Motor lines: 9.
45in. 5 line 4 phase can be used for ordinary uln2003 chip driver, With convenient use, Connect to the 2 phase, Support the development board, direct docking. A, b, c, d four-phase led indicates the status of the stepper motor work. Come with a standard interface, when used directly pluggable.
2. Longruner #ad
Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire #adLongruner #ad
- Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs. Good after-sales service. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board. A, c, b, d four-phase led indicates the status of the stepper motor work.
5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Stepper motor with a standard interface. Cable length: about 20cm /8-inch. Motor diameter: 1. 1 inches. Wire length：9. 05 inchs.
|Warranty||1 year warranty|
3. LAFVIN #ad
LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino #adLAFVIN #ad
- Package content: 5 set 28byj-48 stepper motor + Uln2003 Driver Board +20pcs female to male Dupont cable as a gift. 5 line 4 phase can be used for ordinary uln2003 chip driver, connect to the 2 phase, support the development board，With convenient use, direct docking.
A, c, b, d four-phase led indicates the status of the stepper motor work. Stepper motor with a standard interface. Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in.
4. KeeYees #ad
KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino #adKeeYees #ad
- This is a good parts kit for an arduino and raspberry pi based RC car project. Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber.
It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage.
Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability. It has the strong driving ability, low calorific value and strong anti-interference ability. Motor drive controller: l298n used as the main driver chip.
5. GeeekPi #ad
GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino #adGeeekPi #ad
- Stepper motor with a standard interface could be connected with Driver Board easily; A, B, C, D four-phase LED indicates the status of the stepper motor work. 5pcs stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi.
5 line 4 phase can be used for ordinary uLN2003 chip driver, support the development board, with convenient use, connect to the 2 phase, direct docking. Package includes:5 x stepper motor, 5 x ULN2003AN Driver Board, 30 x Female-to-female jump wire.
6. Adafruit #ad
Adafruit Motor/Stepper/Servo Shield for Arduino v2.3 Kit #adAdafruit #ad
- Instead of using a latch and the arduino's pwm pins, such as the uno, and since it's i2c you can also connect any other i2c devices or shields to the same pins. As of 3/21/2014 we are shipping motor shields with the terminal blocks, and power jumper pre-soldered on.
You'll still need to do a little soldering to put on the shield-headers or stacking headers but it should be even easier and faster to get started! It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well.
This chip handles all the motor and speed controls over I2C. Instead of a l293d darlington driver, we now have the tb6612 mosfet driver: with 1. 2a per channel and 3A peak current capability. New version 2.
3! completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project. This also makes it drop-in compatible with any Arduino, Due, we have a fully-dedicated PWM driver chip onboard. Only two pins sda & scl are required to drive the multiple motors, Leonardo and Mega R3.
7. TIMESETL #ad
TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects #adTIMESETL #ad
- Easy to use no assembly required. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. High quality main driver chip l298n, strong anti-interference, strong driving ability, afterflow diode protection, low calorific value, more stable and reliable for Arduino projects.
Just wire up motors and power, easy to use. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
High efficient double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient. This l298n board comes ready to go.
|Model||L298N motor controller|
8. HiLetgo #ad
HiLetgo 5pcs ULN2003 28BYJ-48 4-Phase Stepper Motor with 5V Drive Board for Arduino PI PIC Raspberry Pi #adHiLetgo #ad
- Diameter: 28mm. Voltage: 5V. Hiletgo stepper Motor+ Driver Board. Speed down stepping motor. Stepping angle: 5. 625 x 1/64.