As an Amazon Associate I earn from qualifying purchases.
1. Treedix #ad
Treedix 5-12V ZVS Low Voltage Induction Heating Power Supply Module with Coil Power Supply Heating Power Supply Module #adTreedix #ad
- Zvs heating power source module, with heating coil included. Ensure all the components welding right, power line connected in the right way, then to set up an electric circuit. The current / voltage is directly linked to what you're heating.
The heating coil can be soldered onto the PCB. The width of the object to be heated should be between 1/3 and 1/2 of the inner diameter of the heating coil, and it should not exceed 2/3. Input voltage：dc 5v~12vthis voltage range is the voltage during operation, not the voltage when the power supply is unloaded.
2. KOOBOOK #ad
KOOBOOK 1Pcs 1000W ZVS Low Voltage Induction Heating Board Module Flyback Driver Heater 12V-48V DIY #adKOOBOOK #ad
- The circuit board using double-sided fiberglass board, continuous work, please add a fan to blow down from above, mainly copper traces are used to widen use the entire back surface of the resonant circuit common, to the resonance capacitors and other components cool.
The higher the voltage, so to eradicate the actual situation to select the input voltage, the greater the heating current when the same thing, the effect is better. But at the same time heat is also large, the general use of the words 24V or 36V power supply is enough.
Can only be used for small parts diy players do hardening, silver, uniform heating fast, aluminum and other metals, copper, annealing and other heat treatment.
Also can be used with a graphite crucible melting gold, very convenient. Not for industrial production. This section of induction heating using low-voltage DC power supply 12-48V, maximum current 20A, maximum power 1000W, long-time working power 500-800W. The kit contains a full set of driving circuit elements and brass. Buyers need to bring their own power and cooling unit.
3. Yosoo #ad
12v-36V Zero Voltage SwitchingZVS Tesla Coil Flyback Driver Circuit for SGTC Marx Generator/Jacob's Ladder + Ignition Coil #adYosoo #ad
- A flyback disk circuit, as well as zero switching, ignition coil voltage, disk used for masses of fans called "zvs circuit. ". Can reach 50-100w of 12v input power, 24v max input can reach more than 200W, the power supply current is preferably greater than 10A.
High voltage direct current output, voltage input voltage of about 1000 times. Widely used in the spark Gap Tesla unit sgtc and Jacob, stairs, generator, Marx, etc. 12-36vdc input recommend 24V.
4. IJJ #ad
ZVS 20A 1000W Low Voltage Induction Heating Module Flyback Heater Driver Board #adIJJ #ad
- Tested 53v power supply when working properly. 24v input with no load current of 3A. Flyback Heater Driver Board. Zvs 20a 1000w low voltage Induction Heating Module. 48v input with no load current of 6A.
5. Tangxi #ad
DIY High Frequency Induction Heating Machine Module, Tangxi 40A 12V-48V 1800W ZVS Induction Heater Heating Board Module Flyback Driver Heater #adTangxi #ad
- This product has a maximum power of 1800W, super PCB layout design and super heat sink, superior heat dissipation effect. 12-48v low voltage dc power supply with a maximum current of 40A. It can work continuously for several hours with good heat dissipation.
Can use graphite crucible to melt gold, silver, aluminum and other metals, heating evenly, copper, fast and very convenient. With a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc. It is recommended not to exceed 48V 35A to prevent accidents and damage.
6. eboxer-1 #ad
Eboxer-1 2500W Induction Heating Board DC 12V ZVS Induction Heating Board Flyback Driver Heater high Frequency Induction Heater Module with DIY Spiral #adeboxer-1 #ad
- The heating board is made of PCB, with stable performance. Use the large power supply of the for better cooling. The power cord is completely covered with copper cover, which can increase current and calorific value.
6 irfp260 and 12 parallel resonant capacitors are used for high power and efficiency. The output terminals use three copper columns in parallel to connect to other outputs, such as the FBT.
7. ANMBEST #ad
ANMBEST High Frequency ZVS Driver Module 5V-12V 120W Low Voltage Induction Heating Power Supply Board with Heating Coil #adANMBEST #ad
- Attention: confirm that all components are soldered correctly, ignition coil, and that the positive and negative poles of the power cord are not reversed. . Push the ignition coil primary 5 + 5 turn, about 30 w.
For long-term use, it is recommended to use a copper tube as the coil and cool it with water. Maximum power: 120W. Led indication: with blue LED power indicator, easily confirm whether the device is powered on. Operating voltage: 5v-12v.
Heating coil: the width of the object to be heated should be between 1/3 and 1/2 of the inner diameter of the heating coil, and the maximum should not exceed 2/3! The diameter of the heating object should be controlled within 20mm as much as possible. Connect the load heating coil, and then turn on the power! Do not power on without load! Operating time: when induction heating, it is usually 5 minutes to power off and cool down.
8. MeterMall #ad
MeterMall 1800W/2500W ZVS Induction Heater Induction Heating Machine PCB Board Module Flyback Driver Heater Cooling Fan Interface+ Coil 1800W Electronics Accessories #adMeterMall #ad
- The heating plate is made of military-grade PCB, and the performance is stable. The power line is fully covered with copper cover design, which can increase the current and heat generation. The output terminal uses three M4 copper columns in parallel, which can be connected to other outputs such as high voltage package.
Using oversized and large power heat sink to dissipate heat better. Using six irfp260 and 12 capacitors in parallel resonance, the power is high and the efficiency is high.